Search

Durethan B30SF 000000
_More Info
_Data sheet ASTM (PDF)

Data sheet
PA 6, non-reinforced, injection molding, suitable for food-contact
ISO/ASTM
ISO Shortname:ISO 16396-PA 6,,GR,S14-030
Property Test Condition Unit Standard guide value
dry as molded conditioned

Mechanical properties (23 °C/50 % r. h.)
Tensile modulus 1 mm/min lb/in² ASTM D 638 464000 159000
Tensile stress at yield - lb/in² ASTM D 638 11600 5800
Tensile elongation at yield - % ASTM D 638 4.0 20
Tensile elongation at break - % ASTM D 638 35 > 50
Tensile stress at break - lb/in² ASTM D 638 7250 8700
Izod notched impact strength 73 °F, 0.125 in ft·lb/in ASTM D 256 1.1 14
Flexural modulus - lb/in² ASTM D 790 392000 102000
Flexural stress at 5 % strain lb/in² ASTM D 790 16700 5080

Thermal properties
Deflection temperature under load, Unannealed 66 psi; 0.157 in °F ASTM D 648 356
Deflection temperature under load, Unannealed 264 psi; 0.157 in °F ASTM D 648 140
UL94 Flame Class Thickness tested: 1.5 mm Class UL 94 V-2
UL94 Flame Class Thickness tested: 3.0 mm Class UL 94 V-2
Relative temperature index, mechanical with impact Thickness tested: 1.5 mm °C UL 746B 65
Relative temperature index, mechanical without impact Thickness tested: 1.5 mm °C UL 746B 75
Relative temperature index, electrical Thickness tested: 1.5 mm °C UL 746B 105

Electrical properties (23 °C/50 % r. h.)
Dissipation factor 50 Hz - IEC 60250 0.05 2.3
Dissipation factor 1 MHz - IEC 60250 0.07 0.4
Volume resistivity Ohm·m IEC 60093 1E13 1E10
Surface resistivity Ohm IEC 60093 1E13 1E12
Dielectric strength 0.118 in V/mil IEC 60243-1 762 889
Dielectric constant, Tinfoil electrodes 50 Hz - IEC 60250 3.8 20
Dielectric constant, Tinfoil electrodes 1 MHz - IEC 60250 3.4 4.6
比较跟踪指数CTI V ASTM D 3638 600

Other properties (23 °C)
Density lb/in³ ASTM D 792 0.041
Specific gravity - ASTM D 792 1.14
Disclaimer
Disclaimer for commercial products
This information and our technical advice - whether verbal, in writing or by way of trials - are given in good faith but without warranty, and this also applies where proprietary rights of third parties are involved. Our advice does not release you from the obligation to verify the information currently provided - especially that contained in our safety data and technical information sheets - and to test our products as to their suitability for the intended processes and uses. The application, use and processing of our products and the products manufactured by you on the basis of our technical advice are beyond our control and, therefore, entirely your own responsibility. Our products are sold in accordance with the current version of our General Conditions of Sale and Delivery.
Test values
Unless specified to the contrary, the values given have been established on standardized test specimens at room temperature. The figures should be regarded as guide values only and not as binding minimum values. Kindly note that, under certain conditions, the properties can be affected to a considerable extent by the design of the mould/die, the processing conditions and the coloring.
Processing note
Under the recommended processing conditions small quantities of decomposition product may be given off during processing. To preclude any risk to the health and well-being of the machine operatives, tolerance limits for the work environment must be ensured by the provision of efficient exhaust ventilation and fresh air at the workplace in accordance with the Safety Data Sheet. In order to prevent the partial decomposition of the polymer and the generation of volatile decomposition products, the prescribed processing temperatures should not be substantially exceeded. Since excessively high temperatures are generally the result of operator error or defects in the heating system, special care and controls are essential in these areas.
Conditioning
Conditioning in accordance with ISO 1110 (70 °C; 62 % r.h.)
LANXESSDEUTSCHLAND GMBH|D-50569 COLOGNE
Date: 2021-08-13 17:29:25.0